Part No: RXSOL-20-2015-210
Suitable for soften up / remove baked on drying oils and also used after animal and vegetable oils, fish oils, tall oils, tung oil etc. Gentle & sutable for tank cleaning operation and depositing area.
Well balanced alkaline cleaner. It is free hydrocarbon solvents. Gentle & suitable for tank cleaning operation. A very strong alkaline cleaner, which can be used to soften up / remove baked on drying oils and also used after animal and vegetable oils, fish oils, tall oils, tung oil etc. It is a low toxic product with an exceptional solvency power on soil & oily matter.It is free from Hydrocarbon solvents , Biodegradable and minimizes the extreme hazards to personnel in handling materials.
It can be used as a general purpose cleaner to remove oil and grease deposits. First of all flush the system with cold water to prevent evaporation rates and polymerization then the most economical method of using RXSOL-20-2015-210 is by direct injection followed by recirculation washing, using tank cleaning machines. Spraying Method - Using LAC as delivered in drums, spray onto areas where residue remains following rough washing leave for 10-45 minutes (but do not allow to dry), then butterworth at maximum pressure and warm water 60oC for at least 3 hours, checking that there is no foam remaining in the final stages. Inspects tanks(s) and if desired result has been achieved fresh water rinse and dry.
** Make sure to take all safety precautions are followed when handling / spraying RXSOL-20-2015-210
Injection Method – not applicable.
Vegetable and Animal Oils (Cleaning Procedure)
For effective cleaning of animal and vegetable oils the first cleaning step is of utmost importance. Vegetable oils are divided in:
- Non-drying products
- Semi-drying products
- Drying products
- Fatty acids Non Drying Products
1. Butterworth the tank with seawater or freshwater with a temperature 20°C. above the melting point of the product to be cleaned. After sufficient pre-cleaning of at least 1.5 hours the temperature can be increased. Drying and Semi-drying ProductsThese are oxidising products and through reaction with oxygen they will dry and harden. Tank cleaning should be executed as soon as possible after discharge. High temperatures (e.g. cleaning or steaming) and heated cargoes in adjacent tanks should be avoided.
2. Butterworth the tank with cold to warm seawater or freshwater.If the product has a higher melting point Butterworth the tank with seawater or freshwater with a temperature maximum 10°C above the melting point of the product. After sufficient pre-cleaning of at least 1.5 - 2 hours the temperature can be increased. Fatty Acids or vegetable/animal oils with high free fatty acid contentsee the cleaning suggestion of Fatty Acids.
3. If seawater was used in step 1 it is of utmost importance to flush/rinse the tank with freshwater before cleaning as per step 3 is continued.
4. Final cleaning Prepare the following solution in freshwater (see table):
-
Make solution a emulsification 0. 4 % RXSOL-20-2015-210 Butterworth the tank with the prepared solution for 1, 5-2, 0 hours by recirculation. The necessary temperature can be achieved / maintained by means of heating coils, cargo heat exchanger or Butterworth heater. Depending on the amount of product residues the solution can be used for 1 to 4 tanks. On some vegetable/animal oils it is recommended to saponify additionally the product residues (see table): Therefore prepare one of the following solutions (B or C) in
freshwater (see table):
5. continuedButterworth the tank with the prepared solution for 1, 5-2, 0 hours by recirculation. The necessary temperature can be achieved /maintained by means of heating coil (service tank) cargo heat exchanger or Butterworth heater. If RXSOL-20-2015-210 is used the cleaningtemperature should be 60-70°C. And If sodium or Potassium Hydroxide is used the cleaning temperature should be 60.C. If RXSOL-20-2015-210 is used the cleaning temperature can be 70-80°C. Depending on the amount of product residues the solution can be used for 1 to 3 tanks.
6. Butterworth the tank 1 hour with hot seawater
7. Rinse the tank with fresh water
8. Inspect the tank; if white residues or a white film is present (calcium/magnesium soaps or carbonate) Butterworth the tank with one the following solution: 3-5% RXSOL-16-1011-210 ( www.rxmarine.com/metal-brite-210-ltrs-pkg ) The cleaning temperature should be moderate (50°C.) Use heating coils not the Butterworth heater.
9. Flush the tank with fresh water
10.Ventilate, mop and dry the cargo tank.
-
Removes grease, oil, carbon deposits, soil and grime.
-
Keeps loosened deposits in suspension preventing re-deposition.
-
Low toxic. , Non-flammable.
-
Free from hydrocarbon solvents.
-
Effective and economical in use , Water-based cleaner.
-
RXSOL-20-2015-210 has numerous cleaning applications including removal of greases, waxes,
-
oil, sludge, soot, carbon deposits and general dirt and grime.
-
Non-corrosive to ferrous metals. Suitable for all tank-coatings.
-
Can be used for gas and hydrocarbon freeing of tanks.
-
Can be used for deodorizing
- Contains wetting agents.
NOTE : Acts as an acid-neutralizing agent.
LAC Alkaline Tank Clean Liquid supplier in Deen Dayal Upadhyay - Kandla, Mundra Gandhidham, Sikka jamnagar, Hazira Surat, Mumbai JNPT, Manglore, Goa, Ennore, Chennai, Visakhapatnam, Gangavaram, Kolkata Haldia, Buzbuj, Paradip, Fujairah, Sharjah, Korfakkan, Abudhabi, Ajman, Muscat, Salalah Oman, Sudan Nairobi Kenya Africa, Yemen
DRYING OILS.
CLEANING TIPS : PREWASH WITH COLD SEA WATER THEN MAIN WASH WITH HOT SEA WATER AND INJECT CAUSTIC POTASH LIQUID Based cleaner ( LAC)
CHINA WOOD OIL POPPYSEED OIL
CANDLE NUT OIL RUBBERSEED OIL
HEMPSEED OIL SAFFLOWER OIL
LINSEED OIL SOYA BEAN OIL
MENHADEN OIL TALL OIL
MUSTARDSEED OIL TUNG OIL
OTTICEA OIL WALNUT OIL
PERILLA OIL
SEMI-DRYING OILS.
Cleanig TIPS : PREWASH WITH COLD SEA WATER THEN MAIN WASH WITH HOT SEA WATER AND INJECT CAUSTIC POTASH LIQUID (LAC)
BABASSU OIL COD OIL
CODLIVER OIL COTTONSEED OIL
CROTON OIL HERRING OIL
JAP FISH OIL MAIZE OIL
SARDINE OIL SESAME OIL
SHARK OIL SUNFLOWERSEED OIL
WHALE OIL WHEAT OIL
NON-DRYING OILS.
CLEANING TIPS : PREWASH WITH HOT SEA WATER THEN MAIN WASH WITH SEA WATER AND INJECT CAUSTIC POTASH BASED LIQUID ( LAC )
ALMOND OIL ARACHIS OIL (GROUNDNUT)
CAMPHOR OIL CANADA OIL
CARAPA OIL CHASHEW NUT OIL
CASTOR OIL COCONUT OIL
COHUNE OIL CURI CURI OIL
GERANIUM OIL LARD OIL (ANIMAL)
NEATSFOOT OIL OLIVE OIL
PALM OIL PINE OIL HOT
RAPESEED OIL (COLZA) RICE OIL
SEAL OIL SPERM OIL
TACUM OIL TALLOW OIL
TEA SEED OIL
LAC Tank cleaner is classified alkaline marine tank cleaning chemicals.
If cargo / tank is not suitable to use alkaline cleaner then substitute of this product is Neutral Based cleaner i.e HCF Remover HD 210 Ltr
Re-circulation Method :
Fill tank with fresh water and heat up to warm 50 oC .IF a drop line is available on the tank line system, then start to circulate the water and add the required amount of Caustic flakes and LAC to make a 2.5% solution. A stronger solution can be made, but be advised that too much Caustic and too high temperature will result in white powder all over the tank. Under normal circumstances, between 2.5% and 4.5% will be sufficient strength. If there is no drop line, then lower butterworth hoses into the tank from the pump stack header without machines attached and circulate through these hoses while you fill the solution material.
* Use a strainer at the pump stack when circulating any solution.*
Tank Lining – Stainless / Epoxy / Phenolic
Suitable for soften up / remove baked on drying oils and also used after animal and vegetable oils, fish oils, tall oils, tung oil etc. Gentle & sutable for tank cleaning operation and depositing area.
Safety Data (MSDS)
| Product Name | RXSOL-20-2015-210 |
| Product Type | LAC Tank & Industrial cleaner |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
Stock Point : Mumbai, Kandla, Kolkata, Chennai, Visakhapatnam, Fujairah, Muscat, Nairobi
| Phone | +91 22 27815540-43 |
| Fax | +91 22 2781 1318 :::AOH :0091 9821214367 |
| 123@rxmarine.com |
Alkaline cleaner Declaration according to recommendation 89/542/EEG.
|
Blend of SURFACTANT ANIONIC NON-IONIC, LAB |
Proprietory Blend |
40-50 |
| Butoxydiglycol | 112-34-5 | 1-5 |
|
Sodium Nitrite |
7632-00-0 |
0.1-1 |
|
C9-11 Pareth-6 |
68439-46-3 | 1-5 |
|
Butoxyethanol |
111-76-2 |
1-5 |
| Sodium Xylenesulfonate | 1300-72-7 | 1-5 |
| Sodium Hydroxide | 1310-73-2 | 1-5 |
| Tetrasodium EDTA | 64-02-8 | 0.1-1 |
| CI 15620 | 1658-56-6 |
0.1 |
|
Environmental Hazards |
None |
|
Human Health Hazards |
Moderates |
R 35:Causes skin burning effects
|
Inhalatin |
Move to fresh air and seek medical advice attention. |
|
Skin Contact |
Rinse with running water and soap. Skin care. Remove contaminated clothes. |
|
Eye Contact |
Flush with running water for at least 15 minutes Immediately . |
|
Ingestion |
Vomiting is dangerous , seek medical attention. |
Non Combustible Porduct
|
Suitable |
N.A. can use foam dry Co2 , water-spray. |
|
Not suitable |
Not applicable |
|
Special |
Not applicable |
|
Protection of fire Fighter |
Not applicable |
Special protective equipment for fire-fighters: Wear protective equipment.
|
Enviromentel Precaution |
Direct flow into drainage system, surface or ground water is prohibited. |
|
Cleaning Method |
Flush Spill Area with Water and remove with liquid-absorbing material like foam sand,sawdust etc.. |
|
Condition to Avoid |
Non flammable but avoid direct heating |
|
Materials to Avoid |
Do not subject to Acidic / Oxidizing Agents |
|
Handling |
Keep Container Tightly Closed |
Note:Eyewash facilities require at workplace The product causes corrosion on skin and mucous membranes Pl. Note that In case of discharge of acidic or alkaline products into the sewerage system the pH must be in the range of 6-10 since higher or lower pH values may damage the sewerage system or impair biological dosage treatment plants. So that for maintaining pH we have to add acidic / basic medium neutaliser . For example if pH is less than 6 basic neutraliser is required and if pH is more than 10 acidic nature neutraliser is required. For details of any guideline pl. Visit our technical website www.rxmarine.com
Dilute in water (always use plastic jar and RXSOL should be added to water never add water to RXSOL.)
Personal protection :
|
Respiratory System Protection |
Approved respirator must be worn when spraying |
|
Eye Protection |
Cear eye protection (on possibility of contact ) |
|
Hand protection |
Cear PVC chemical resistance protective glove |
Product Properties:
|
Appearance |
Slight Yellow - clear liquid |
|
Density |
In g/cm3 at 20°C: 1.21 |
|
Compatibility |
|
|
Metal |
No known effect |
|
Rubber |
No known effect |
|
pH |
Alkaline ( 13 ) |
|
Flash point |
Not Applicable |
|
Solubility |
100% soluble in water |
|
Packaging |
Size (in Litres)220 Ltrs |
|
Hazardous Decomposition Products |
Do not occur if stored and used as directed. n FIRE combustion CO, CO2 , NH3 , SOX etc hazardous gas produced |
NOTE : Avoid Contact With Acid
Comment - Not applicable , 100% Soluble in water
95 % added surfactants are biodegradable as per by international regulation .This material must be disposed with local national regulations.
As per guide line of local rules and regulation and before disposal and neutralization pl. refer 07 article.
| Proper Shipping Name | ||||
| UN | ||||
| Proper Shipping Name |
Alkaline Solution |
|||
| UNNo. | 1824 | |||
| Hazard Class | 8 | PackingGroup | II | |
| Road/Rail(ADR/RID) | ||||
| Proper Shipping Name |
Alkaline solution |
|||
| ADR UN No. | 1824 | |||
| ADR Hazard Class | 8 | Tremcard |
80S1824 |
|
|
Sea(IMDG) |
||||
| Proper Shipping Name |
Alkaline solution |
|||
| IMDG UN No. | 1824 | |||
| IMDG Hazard Class. | 8 | IMDG Pack Group. | II | |
| IMDG EmS | F-A, S-A | IMDG subrisk |
N/A |
|
| IMDG Labels |
8 |
IMDG Flash point |
N/A |
|
|
Air(ICAO/IATA) |
||||
| Proper Shipping Name |
Alkaline solution |
|||
| ICAO Un No. | 1824 | |||
| ICAO Hazard Class | 8 | ICAO Packing Group. | II | |
| ICAO subrisk |
N/A |
ICAO Labels |
8, CAO |
|
| ICAO Flashpoint | N/A | |||
|
DOT/ CFR (US Department of Transportation) |
||||
| DOT Proper Shipping Name |
Alkaline solution |
|||
| Hazardous Material |
Sodium hydroxide |
|||
| Hazard Class | 8 | Identification Number | UN 1824 | |
| Product RQ (lbs) | 3640 | DOT subrisk | N/A | |
| DOT Labels | 8 | DOTFlashpoint |
N/A |
|
Classification and labelling according to Chemicals Hazard Information and Packaging Regulations (CHIP). Symbols of danger :- C Corrosive
|
R phrases |
R 35 : Causes severe burns |
|
S-phrases |
S2: Keep out of reach of children S26 :In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. S28 : After contact with skin, wash immediately with plenty of water. S37/39 : Wear suitable gloves and eye/face protection. |
This information is based on our current level of knowledge and relates to the product in the state in which it is delivered. It is intended to describe our product from the point of view of safety requirements and is not intended to guarantee any particular propertie
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.