Part No: RXSOL-20-3300-210
RXSOL-20-3300-025 successfully replaces the traditional cleaner , this product is safer for use, storage and transportation and reduce your costs by 10 - 15%. This product dissolve and loosen deposits in the TANK and increase the permeability layer z
RXSOL-20-3300-025 successfully replaces the traditional cleaner , this product is safer for use, storage and transportation and reduce your costs by 10 - 15%. This product dissolve and loosen deposits in the TANK and increase the permeability layer zones to mix with water.
This is a very strong polymer based cleaner which can be used to soften up / remove baked on drying oils. It is low toxic product with an exceptional solvency power on soil & oily matter. It is free from hydrocarbon solvents, Biodegradable minimizes the extreme hazards to personnel in handling materials.
it finally dissociate slop emulsion to separate oil and water .This provide us with ability to dispose of waste solution.
Suitable for cleaning of Heavy oils, Black oil, Mineral oil Products. Phthalates paraffin's vegetable oils Odour intensive products.
Using-Procedure:-First of all flush the system with cold water to prevent evaporation rates and polymerization then the most economical method of using RXSOL-20-3300-025 is by direct injection followed by recirculation washing, using tank cleaning machines.
Spraying Method:-Using RXSOL-20-3300-025 as delivered in drums, spray onto areas where residue remains following rough washing leave for 10-45 minutes (but do not allow to dry), then butterworth at maximum pressure and warm water 60oC for at least 3 hours, checking that there is no foam remaining in the final stages. Inspects tanks(s) and if desired result has been achieved fresh water rinse and dry.
**Make sure to take all safety precautions are followed when handling / spraying RXSOL-20-3300-025
Injection Method:- Not applicable.
Re- Circulation Method:- Fill tank with fresh water and heat up to warm 50oC . IF a drop line is available on the tank line system, then start to circulate the water and add the required amount of Caustic flakes and RXSOL-20-3300-025 to make a 2.5% solution. A stronger solution can be made, but be advised that too much Caustic and too high temperature will result in white powder all over the tank. Under normal circumstances, between 2.5% and 4.5% will be sufficient strength. If there is no drop line, then lower butterworth hoses into the tank from the pump stack header without machines attached and circulate through these hoses while you fill the solution material.
Other Popular Method for TANK CLEANING :::
Tank Cleaning Sludge/ Lube Oils / Slope-Black Oil
1 ) Fill the tank with 1-35 litres per ton wash water.Best results are obtained when water is heated to a temperature between 65°C & 80°C then stripped constantly and transferred to a holding tank for separation.The time for this will vary depending on amount of RXSOL-20-3300-025 used & nature of oil being cleaned.Generally,12 hours should be sufficient before the water phase can be removed.
2) Direct Cleaning.Spray directly RXSOL-20-3300-025 on tank surfaces to be cleaned, left for at least 30 minutes.Finally wash with hydrogating (high pressure) machine. Hot water between 50°C & 80°C recommended.
**Use a strainer at the pump stack when circulating any solution.** Tank Lining– Stainless / Epoxy / Phenolic.
Necessary concentration in water only 0,2 to 0,4 %
Oil and Sludge remover
RXSOL-20-3300-025 is also recommended for local cleaning & degreasing of engine rooms, bilges & tank tops. It may be applied by brush, spray, immersion, soaking, or any other conventional means.RXSOL-20-3300-025 is used neat. Allow a residence time of at least 20- 45 minutes where possible, to ensure good penetration & emulsification. Finally wash the system with hot water & high pressure.The emulsion residue after cleaning must be allowed to separate in a holding tank for atleast 3-5 hours before passing through an oily water separator.
NON-TOXIC
NON-INFLAMMABLE
NON-CORROSIVE AND NON¬ IRRITANT.
FLASHPOINT: >78 DEG.C
VISCOSITY: AT 20 DEG.C. 10 MPAS (MAX)
DENSITY: AT 20 DEG.C-910 KG/M3 (APPROX.)
PH IN 1% DISPERSION: 7 (APPROX.)
Oil Sludge Cleaner Heavy VOLC manufacturer supplier distributor in Mumbai, Kandla, Kolkata, Vizag, Chennai, India, Fujairah, Dubai, Sharjah, UAE, Gulf, Middle East, Muscat Oman, Kenya Africa. Get the best quality of Oil Sludge Cleaner Heavy VOLC at a competitive price from us. We have ready stock of Oil Sludge Cleaner Heavy VOLC in India, UAE Gulf, Oman, Kenya Africa. Contact us for bulk as well as small orders.
Oil Sludge Cleaner
Heavy-Duty Emulsifying Degreaser for Sludge, Tar & Oily Residues
Oil Sludge Cleaner is a high-performance cleaning solution formulated to break down and remove heavy oil deposits, sludge, tar, waxy residues, and hydrocarbon buildup from tanks, pipelines, bilges, engine rooms, and cargo areas. It is designed to emulsify thick oily contaminants, allowing for easy flushing and cleaning with water.
Key Features:
-
Powerful Degreasing Action: Penetrates and dissolves tough sludge, crude oil, and heavy fuel residues.
-
Emulsifies Oil and Sludge: Converts sticky hydrocarbons into pumpable liquid form for easy removal.
-
Marine and Industrial Use: Ideal for use in ships, refineries, oil storage tanks, engine compartments, and machinery cleaning.
-
Water Rinsable: Forms stable emulsions that can be easily flushed out with hot or cold water.
-
Non-Flammable Formula: Enhances safety during onboard use or confined tank applications.
-
Versatile Application: Suitable for spray, circulation, and manual cleaning methods.
Typical Applications:
-
Crude oil & fuel oil tank cleaning
-
Bilge & engine room degreasing
-
Sludge removal from separators & settling tanks
-
Pipework and heat exchanger cleaning
-
Offshore rig & terminal maintenance
Usage Instructions:
-
Dilute as per cleaning requirements (commonly 5–25% in water or neat use for heavy deposits).
-
Allow to soak and emulsify sludge before flushing.
-
Always follow safety guidelines and use appropriate PPE.
CLEANING AGENT: MIXTURE OF NON-IONIC AND ANIONIC SURFACE ACTIVE • COMPOUNDS OIL/SLUDGE REMOVER IN EQUIPMENT AND PLANT USED DIRECT OR MIXED WITH WATER BY COLD SPRAYING,BRUSHING AND DIPPING, SOLUBLE IN ALL HYDROCARBONS AND DISPERSABLE WITH WATER.
- Removes grease, oil, carbon deposits, soil and grime.
- Keeps loosened deposits in suspension preventing re-deposition.
- Low toxic. , Non-flammable.
- Free from hydrocarbon solvents.
- Effective and economical in use , Water-based cleaner.
- RXSOL-20-3300-025 has numerous cleaning applications including removal of greases, waxes, oil, sludge, soot, carbon deposits and general dirt and grime.
- Non-corrosive to ferrous metals. Suitable for all tank-coatings.
- Can be used for gas and hydrocarbon freeing of tanks.
- Can be used for deodorizing
- Contains wetting agents.
Characteristics:-
High penetration & emulsification , Reduces down time.
For cleaning of machinery parts, bulk heads, decks, bottom plates & any oil/grease dirty areas.
Used for cargo tank cleaning of mineral oils and petroleum based chemicals, Sludge etc .
Safety Data (MSDS)
| Product Name | VOLC Sludge Cleaner RXSOL-20-3300-210 |
| Product Type | Industrial Marine cleaner |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
| Phone | +91 22 65113333 / 5555 / 9999 |
| Fax | +91 22 2781 1318 :::AOH :0091 9821214367 |
| mail@rxmarine.com |
|
Chemical Name |
Concentration |
CAS Number |
EC Number |
R Phrases* |
Symbols |
|
Faty alcohal ethoxylate |
Mix |
|
|
22-36/38 |
Xn |
*See Section 16
|
Environmental Hazards |
None |
|
Human Health Hazards |
Moderates |
|
NOTE |
Person-related safety precautions |
|
After inhalation |
On Inhalation move to fresh air / Arificial respiration . Get medical attention. |
|
After skin contact |
Instantly wash with water and soap and rinse thoroughly. Generally Non Irritating , Protective clothing require. |
|
After eye contact |
Rinse opened eye for several minutes under running water. If symptoms persist, consult doctor. |
|
After swallowing |
Harmful, if ingested,Do not induce Vomiting. Get medical attention. |
Extinguishing Media:-
|
A. Suitable Foam |
dry Co2, water spray |
|
B. Not suitable |
Not applicable |
|
C. Special |
Not applicable |
|
|
Do not use Direct water jet |
|
Protection of fire |
Fighter Masked with Air Respirator |
Care for environmental protection Prevent material from reaching sewage system, holes and cellars. Dilute with much water.PROCEDURE for cleaning/collecting Remove RXSOL VOLC with absorbent materials or mechanically .And dispose accordance with section ,Then flush with water and ventilate well.NOTE Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust).
|
Handling |
Eyewash facilities require at workplace. |
|
Storage |
General Storage , container should be tightly. |
|
Methods of cleaning |
Flush Spill Area with Water. |
|
Note |
Keep Container Tightly Closed. |
|
Enviromental Precaution |
Readily Bio-Degradable , missible with water , low toxicity , No environmental problem on correctly usage. |
|
Personal Proctection |
|
|
Respiratory System Protection |
Breathing equipment Not required |
|
Eye Protection |
wear eye protection (on possibility of contact) |
|
NOTE |
The product does not contain any relevant quantities of materials with critical values that have to be monitored at the workplace. |
|
Wash hands during breaks and at the end of the work. Avoid contact with the eyes and skin.Keep away from foodstuffs, beverages and food. |
|
|
Protection of hands |
Protective gloves |
|
Eye protection |
Tightly sealed safety glasses |
PRODUCT PROPERTIES:-
|
Appearance |
Clear liquid / Low viscous |
|
|
Odour |
Characteristic / Odorless |
|
|
Density |
In g/cm3 at 15°C: 1.00 |
NOTE : SHELF LIFE 10 YEARS |
|
Boiling Point |
MATERIALS BOILS AT 100°C |
EFFICIENCY : |
|
Compatibility |
|
A . SEA WATER 68% |
|
Metal: |
No known effect |
B. FRESH WATER 78% |
|
pH |
6 +0.5 |
B . FRESH WATER 98.8 % |
|
Packaging |
Order No.: |
Size (in litres) |
|
|
RXSOL-20-2028-025 |
25 , 30 , 210 |
|
TOXICITY LC50 (After 96 hours ) |
IN CONCENTRATE 4460 PPM SLIGHT TOXIC. |
IN DILUTE 9800 PPM PRACTICALLY NON TOXIC . |
|
Condition to Avoid |
Heat, Flame & Other Sources of Ignition |
|
Materials to Avoid |
Do not subject to Reducing /Oxidizing Agents. |
|
Hazardous Decomposition Products |
Do not occur |
|
NOTE |
No decomposition if used according to specifications |
|
Skin Irritation |
Irritant wash with soap water |
|
Eye Irritat |
Moderate irritant , flush with copious amounts of water |
|
Sensitization |
Not Sensitizing . |
|
(All above information as per data available with us) |
|
|
Comment |
Not applicable |
|
Ecotoxicity |
Not applicable , Readily biodegradable |
|
Water hazard class 2 (self-assessment) |
Hazardous for water. |
|
Do not allow product to reach ground water, water bodies or sewage system..Danger to drinking water if even small quantities leak into soil. |
|
This material must be disposed with local national regulations. Product Recommendation Can be burnt under adherence to the necessary technical regulations. Disposal must be made according to official regulations.
Marine pollutant: No.Transport/Additional information Not Dangerous
Hazard designation of product: Xi Irritant.
Irritating to eyes and skin.
Safety phrases
2Keep out reach of children
If swallowed, seek medical attention immediately
26In case of contact with eyes, rinse immediately with plenty of water and
seek medical attention.
27After contact with skin, wash immediately with plenty of water and soap and rinse thoroughly.
4.National regulations
These data are based on our present knowledge. However, they shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship. Department issuing data specification sheet Environment protection department.
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.